48-Input, 96 output button/joystick/LED/trackball/spinner interface. Includes ALL wiring for 2 player controls. Includes LED power cable and USB cable. Please check "more info" link for additional harness requirements for non-RGB LEDs and 4 players.
Warning: Last items in stock!
Full Speed USB 2.0. 48 Inputs, 96 outputs. Upgradeable Firmware.
NO EXTRA WIRING required for most standard installations. All switch wiring supplied. Trackball and spinner simply plug in. RGB LEDs simply plug in.
This board has a total of 176 connections. If you were to hand-wire every LED and switch this would be a total of up to 576 wire ends to strip and connect! Which is why we have done it for you.!
48 inputs each with it's own dedicated microprocessor pin. No interaction or delays, vital for multi-button games such as fighting games.
Emulates a USB keyboard and yet breaks through the USB simultaneously-pressed-switch limit of 6 switches (plus ctrl,alt,shift) which afflicts all USB keyboard devices. This is because it has inbuilt full native USB support, and does not rely on an add-on adaptor.
Also emulates Mouse, Game Controller and Power/Volume Control.
All input pins can be assigned to any keyboard key, gamepad button (including hat switch), mouse button or power/volume control. Also sleep/wake.
Inputs can be assigned as trackball and spinner and our U-Trak and SpinTrak devices plug directly into the board.
Shift function which allows ANY input to be assigned to a shifted secondary keycode and the shift button can have it's own function too so no need for a dedicated extra control panel button.
Self-test LED which gives an instant visible check of your installation.
96 channel LED controller with constant-current drivers. Also 8 high-current 1 amp drivers.
Brand new INTERACTIVE configuration utility which applies and reads back any changes "on the fly".
MAME Defaults pre-loaded.
I-PAC Ultimate I/O retains it's programming after power off. Beware! Not all keyboard encoders do this!
Special version available with ACCELEROMETER chip on board which is configured for "nudge detect" mode.
Full Feature List
|LED test and scripting utility||WinIPAC for reconfiguring controls|
Third-Party Software and SDK Support
What to OrderAll Items Listed on This Store Page
|Example Configurations||Items to Order|
|2 Players using Ultralux RGB or ClassicRGB buttons, U-Trak trackball, Spintrak Spinner||Nothing extra required. Order Board with 2-player harness kit.
LED Power Cable
Ground daisy-chain harness
|4 Players using Ultralux RGB or ClassicRGB buttons, No trackball or Spinner (these are not supported in a 4-P config)||Order standard board/harness (see above)
Order 4-player expansion kit.
|Either of the above but using single-color LEDs such as Ultralux.||Order as above plus one "LED Connection Pack" per 9 LEDs, Also one "Daisy-Chain Harness" per panel for LED common connections.|
|Optional Extras||Extension Harness Pack. This is used for unusually large panels for increasing reach of any longer wires.
PCB Mounting Feet
Wiring Harness Detailed Information
|Player 3-4 Connection Pack||9-LED Single Color Connection Pack|
|Main Harness||Included||32||330mm / 13 inches|
|Daisy Chain Ground harness||Included||32 Links||90mm / 3.5 inches per link|
|LED Power Cable||Included||n/a||1.5 M|
|USB Cable||Included||n/a||1.5 M|
|Extension Harness Pack (Wires replace existing)||Not Included||10||560mm / 22 inches|
|Player 3,4 Connection Pack||Not Included||20 Plus 20 Ground||560mm / 22 inches|
9-LED Connection Pack. Required for each 9 single-color LEDs (Our RGB are pre-wired)
Get wires here
|Not Included||9 plus common||560mm / 22 inches|
See Download Page for latest firmware..
No customer comments for the moment.