PhreakMods CROSSBONE PadHack PCB. XBOX ONE pad hacking made easy.
This product is no longer in stock
Warning: Last items in stock!
Stage 2 kit with populated boards, so you don't need to do any soldering on the crossbone, all parts are installed for you!
Includes: Crossbone PCB, populated with, 20P header for the CROSSBONE, the 4PIN Header for the SYS2 connection, 2x 10PIN Terminal Blocks, 1x 2PIN Terminal Block, and two runs of wire for SWITCH and LT/3K IN connections.
Simply unhook the original top board of the connected PCBs, and replace it with the CROSSBONE for an easy break out of all the inputs, including USB.
Already have a PS360+, the crossbone is made for you.
More than a simple padhack device, the CROSSBONE integrates easily so you to take full advantage of your PS360+, turning your stick into a multi console weapon (XB1, XB360, PS3, PS2, DREAMCAST). The USB Switcher integrated into the CROSSBONE allows you to select your PS360+ enabling PS3/XBOX360 console support without doubling wires or USB connections!
PhreakMods recommends connecting the “switch” line to the HOME/GUIDE button and depressing it upon boot. This sets the USB switch to the SYS2 so that the PS360+ takes over and legacy console support is enabled! Since the switch only needs to be held down for a second when its plugged in and turned on, you retain the use of HOME/GUIDE and you don’t need another switch installed on your case. Smart.
Safety first! Phreakmods has it covered. Mess up a solder on the XBONE Pad? CROSSBONE has a safety net.
The CROSSBONE is equipped with a front end protection diode, preventing you from connectin the voltage in reverse on the main input, which should keep any accidental power swaps from destroying the board.
CROSSBONE STAGES Explained - Get what you want and how you want it. (A Great Collaboration Between Paradise Arcade and Jasen's Customs)
STAGE 1: The CROSSBONE as designed and sold by PhreakMods. No frills. This requires the most soldering as the CROSSBONE is rather bare with no quick connectors for the external SYS2 connection, no terminals for the buttons/lever to be connected, etc. Those with soldering skills and parts on hand will want this stage. Micro USB Cable to USB is included.
STAGE 2: STAGE 1 plus the parts to populate the CROSSBONE yourself. Save on shipping from multiple vendors and everything arrives ready to solder up. STAGE 2 includes the 20P header for the CROSSBONE, the 4PIN Header for the SYS2 connection, 2x 10PIN Terminal Blocks, 1x 2PIN Terminal Block, and two runs of wire for SWITCH and LT/3K IN connections. Micro USB Cable to USB is included.
STAGE 3: STAGE 2 and completely soldered together. This is the least amount of soldering required for a CROSSBONE XBOX ONE setup. CROSSBONE is completely assembled and ready to attach to a pad. Once attached the three wires can be connected from the XBOX ONE Pad and you are ready to connect buttons and play. This also comes with the 20P Ribbon Cable and USB Cable to connect to a PS360+ outfitted with a 20P header. Micro USB Cable to USB is included.
STAGE 4 (Limited Run): STAGE 3 Kit and a PS360+ with 20PIN Header and 4PIN USB header already connected. Micro USB Cable to USB is included.
Installation, direct from the Creator PhreakMods
Read the directions all the way through before proceeding. Ensure you understand each step. If you get confused, just ask! I’m happy to help/explain a step.
RT and LT can be difficult for new users, and technically you can solder directly to the Hall Effect sensor's pin, but it ensures part longevity if you solder after the resistor and capacitor pair noted in the diagrams and thread. The CROSSBONE does NOT have a 100 Ohm inline resistor on-board.
The STAGE 3 KIT has a wire connected to the SWITCH. You can connect this to the non ground pin of the HOME/GUIDE Button on your fight stick. Upon power up of your stick (when you plug it in or turn your console in) hold the HOME/GUIDE button to activate the PS360+ if it’s attached! You only need to press it for a second as the CROSSBONE will detect this as it boots up and retain the setting as long as the stick remains plugged in!
Additional Considerations for the PS360+ Connection
The USB connector cable included only has 2 wires installed. This is because the 20P ribbon cable carries the required 5V and GND from the USB to the PS360+. Ensure the red pin on the cable gets connected to D+ on both the CROSSBONE and the PS360+ otherwise the system wont work properly.